CronoNorm-NL Series

Wilo Pumps - CronoNorm NL Series

Design Of Wilo Pumps

 

Single-stage low-pressure centrifugal Wilo Pumps with axial suction point, according to EN 733 and ISO 5199, mounted on a baseplate.

 

Application Wilo Pumps

 

  • For pumping heating water (in accordance with VDI 2035), water-glycol mixtures and cooling and cold water without abrasive substances in heating, cold water and cooling water systems
  • For applications regarding the municipal water supply, irrigation, building services, industry, power stations etc. (e.g. circulation, transfer and pressure-boosting tasks)

 

Type key of Wilo Pumps

 

Example NL 40/200B-11/2
NL Standard pump with axial suction
40 DN for the pressure flange
200B Nominal diameter of impeller
11 Rated motor power P2 [kW]
2 number of poles

 

Special features/product advantages of Wilo Pumps

 

  • Reduced life-cycle costs through optimised efficiency levels
  • Bidirectional, force-flushed mechanical seal
  • Low NPSH values, best cavitation properties
  • Shaft coupling with or without intermediate sleeve
  • Shaft deflection satisfies the requirements of ISO 5199

 

Technical data of Wilo Pumps

 

  • Minimum Efficiency Index (MEI) ≥ 0.4
  • Permissible temperature range of -20°C to +120°C
  • Mains connection 3~400 V, 50 Hz
  • Protection class IP 55
  • Nominal diameter DN 32 to DN 150
  • Max. operating pressure 16 bar

 

Scope of delivery

 

  • Wilo Pumps with free shaft end or
  • Wilo Pumps on baseplate with coupling and coupling protection or
  • Completely mounted pump on baseplate with electric motor
  • Installation and operating instructions

 

Materials of Wilo Pumps

 

  • Wilo Pumps housing and pressure lid: EN-GJL-250
  • Bearing bracket: EN-GJL-250
  • impeller: EN-GJL-250
    (special version: G-CuSn10)
  • Shaft: X20Cr13
  • Mechanical seal: AQ1EGG
    (other mechanical seals on request)

 

Description/design of Wilo Pumps

 

  • Wilo Pumps Single-stage low-pressure centrifugal pump as baseplate pump with axial suction piece with flanged bearing bracket and axis mounting for flexibly coupled drives.
  • Spacer coupling (sleeve coupling) available as an option; they make it possible to leave the motor in position when removing the rotor unit
  • Shaft deflection meets the requirements of ISO 5199

 

Commissioning

 

  • If pumps with 2900 rpm are installed inside residential buildings, then corresponding noise reducing measures are to be implemented.
  • Pump curves and specific motor powers depend on the respective fluid being pumped. Pump curves and power vary considerably when fluids are conveyed that differ from water in thickness and/or viscosity. For this, please observe the table “Recommended limit values for dimensioning”.
    The recommended limit values for dimensioning are calculated as follows:
    Qoptimum (volume flow at which the pump reaches its best efficiency), to be read from the individual pump curve; factors Qmin and Qmax , to be taken from the table “Recommended limit values for dimensioning”.Qmin dimensioning = Qmin x Qoptimum
    Qmax dimensioning = Qmax x Qoptimum
    Example: Size NL 32-125
    Qmin = 0.3 x 8 = 2.4 m3/h
    Qmax = 1.2 x 8 = 9.6 m3/h
  • Load-sensitive pump output
    All Wilo standard pumps are equipped with IEC standard motors. The Wilo control devices are suitable for automatic load-sensitive speed control of pumps that are driven by any standard motors of conventional manufacture.
  • Main/standby mode

 

Accessories Wilo Pumps

 

Automatic speed control:

for automatic, infinitely variable pump power control. for additional information, see “Switchgears and control devices” section.

 

Note

 

Motors with efficiency class IE3, other voltages and frequencies on request

 

General notes – ErP (ecological design-) directive

 

  • The benchmark for most efficient water pumps is MEI ≥ 0.70
  • The efficiency of a pump with a trimmed impeller is usually lower than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to reduced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.
  • The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the system.
  • Information on benchmark efficiency is available at www.europump.org/efficiencycharts

 

You might also likeclose